OSHA HAZARD ALERT: SCISSOR LIFT SAFETY

Prevent deaths and injuries – review OSHA’s Scissor Lift Safety Standards with your crews

Over a one-year period, OSHA investigated ten preventable fatalities and more than 20 preventable injuries resulting from a variety of incidents involving scissor lifts. OSHA’s investigations found that most injuries and fatalities involving scissor lifts were the result of employers not addressing:

Fall Protection – Stabilization –  Positioning

Scissor lifts are work platforms used to safely move workers vertically and to different locations in industries including construction and manufacturing.

Scissor lifts are different from aerial lifts because the lifting mechanism moves the work platform straight up and down using crossed beams functioning in a scissor-like fashion. Although scissor lifts present hazards similar to scaffolding when extended and stationary, using scissor lifts safely depends on considering equipment capabilities, limitations and safe practices.

How to Safely Use Scissor Lifts

Employers need to assess the worksite to identify all possible hazards in order to select the appropriate equipment for the task. Employers who use scissor lifts need to evaluate and implement effective controls that address fall protection, stabilization and positioning. Only trained workers should be allowed to use scissor lifts, and employers should make sure that those workers show that they can use a scissor lift properly.

Safe scissor lift use includes properly maintaining the equipment, following the manufacturer’s instructions, providing workers training and needed personal protective equipment (PPE), and implementing safe work practices.

Fall Protection

Scissor lifts must have guardrails installed to prevent workers from falling. Employers should train workers to:

  • Check to see that a guardrail system is in place before working on the scissor lift.
  • Only stand on the work platform; never stand on the guardrails.
  • Keep work within easy reach to avoid leaning away from the scissor lift.

Stabilization

Employers should ensure that scissor lifts are stable and will not tip over or collapse. Some safe work practices to ensure safe, stable conditions for scissor lift use include:

  • Follow the manufacturer’s instructions for safe movement—this usually rules out moving the lift in an elevated position.
  • Isolate the scissor lift or implement traffic control measures to ensure that other equipment cannot contact the scissor lift.
  • Select work locations with firm, level surfaces away from hazards that can cause instability (e.g., drop-offs, holes, slopes, bumps, ground obstructions, or debris).
  • Use the scissor lift outside only when weather conditions are good. Scissor lifts rated for outdoor use are generally limited to wind speeds below 28 mph.

Collapse

Although rare, the collapse of scissor lifts can be prevented if employers:

  • Ensure that safety systems designed to stop collapsing are maintained and not bypassed.
  • Never allow the weight on the work platform to exceed the manufacturer’s load rating.
  • Never allow equipment other than the scissor mechanism to be used to raise the work platform (e.g., using a forklift to lift the work platform).
  • Keep the lift from being struck by other moving equipment on the worksite

Positioning – crushing and caught-between accidents

Positioning the scissor lift to avoid crushing or electrocution hazards is important for safe use. Crushing hazards are present in workplaces using scissor lifts and may expose workers nearby, even those not working on the scissor lift. Scissor lifts present crushing hazards similar to vehicles and other mobile equipment at worksites. Employers should train workers to be watchful when:

  • A moving scissor lift is near a fixed object.
  • A moving vehicle and the scissor lift are operating closely.
  • The scissor lift passes under a fixed object, such as a door frame or a support beam.
  • Positioning the scissor lift to avoid electrocution, arc flash, and thermal burns is important for safely using scissor lifts near energized power lines. Since electricity can arc or jump from the power line to the scissor lift or worker, electrocution can occur even if neither the scissor lift nor the worker touches the power line. Employers should use the following work practices to ensure that scissor lifts are safely positioned implement traffic control measures around the scissor lift to prevent other workers or vehicles from getting too close.
  • Use ground guides when operating or moving the scissor lift around the workplace.
  • •Select work locations that do not approach electrical power sources (e.g., power lines, transformers) by at least 10 feet and that do not pose other overhead hazards (e.g., other utilities, branches, overhangs, etc.).
  • If the job task requires work near an electrical source, ensure that the worker is qualified and has received the required electrical training.

Maintaining Scissor Lifts

Employers must regularly maintain scissor lifts to ensure that they are safe to use (e.g., prevent the lifting mechanism from collapsing). Manufacturer’s maintenance and inspection instructions will generally include how to:

  • Test and inspect controls and components before each use.
  • Ensure that guardrail systems are in good working condition.
  • Verify that brakes once set will hold the scissor lift in position.

Training Workers

Employers must provide workers training on hazards, including how to work safely with or near scissor lifts. Training must, at a minimum, include:

  • Manufacturer’s instructions for operating the scissor lift vertically and while in transit.
  • How to handle materials on the scissor lift, including weight limits.
  • Other worksite hazards workers may encounter when working on a scissor lift (e.g., contact with electrical wires).
  • Reporting any equipment defects or maintenance needs.

Download a copy of this OSHA Hazard Alert here: and set aside time to discuss scissor lift safety.

Recent News

 
Versatile Carmix takes concrete to North Mara Gold Mine in Tanzania
    The gold mine in North Mara is situated in the north-west of Tanzania, at about 100 kilometres east of Lake Victoria and 20 kilometres south of the border with Kenya. The gold mine works an average of 8,000 tonnes of minerals a day and produced 287,188 ounces of gold in 2015. The gold
WORKERS’ MEMORIAL DAY
Workers’ Memorial Day, observed each year on April 28, honors workers killed, injured, or made ill at work. Since 1992, BLS has collected data on both nonfatal work injuries and illnesses that result in days away from work, and fatal work injuries. In 2015, the occupations with the highest number of nonfatal injuries and illnesses
TOP 15 CONSIDERATIONS FOR MAINTAINING UNDERCARRIAGE HEALTH AND PRODUCTIVITY
The undercarriage of a machine represents a significant portion of a piece of equipment’s purchase price. Proper maintenance and operation practices are critical for protecting your equipment investment. Undercarriage maintenance is critical to the overall productivity of a machine. It is the mechanism that gives tracked machines much of their power and stability. It also
Deere Adds 8-Year / 20K Hour Warranty on 944K Electric-Drive Components
John Deere is now offering a 96-month / 20,000-hour power electronic components warranty on the Deere 944K hybrid wheel loader. The warranty is retroactive to existing machines in the field and provided on new 944K loaders through October 31, 2018. The warranty includes a 96-month (eight-year) or 20,000-hour (whichever comes first) non-prorated assurance on wheel
VERMEER SILVER SERIES DRILL RODS COMPOSED OF S135 COMMON GRADE STEEL
  Vermeer’s Silver Series drill rod is composed of S135 common grade steel and is threaded in the same facility as the company’s Firestick drill rod with the same column wall thickness. The Silver Series drill rod is available in four sizes: 1.66-inch, 1.9-inch, 2.06-inch, and 2.375-inch, for use on the D7x11 through the D24x40
CHILE: Construcción regional cae 7,5% y suma dos meses con cifras en rojo
Datos de Cámara Chilena de la Construcción estimaron retroceso de 7,5% en febrero que se suma al -10% de enero. Se busca consolidar esfuerzos público-privados para enmendar el rumbo. Por primera vez desde el año 2002, cuando se comenzó a publicar el Índice de Actividad de la Construcción Regional (INACOR), la Región de Coquimbo inicia

About Us

 
In Tractopart we supply quality construction Parts and Heavy Equipment Parts with excellent discount rate for New , Used Rebuilt & Surplus parts for excavators, Wheel loader dozers, and undercarriage for all heavy equipment brands, we are locate in Miami, Fl

Contact Info

 

At Tractopart we focus on providing high quality parts at a great price. Our parts are subjected to rigorous inspection procedures that allow us to ensure product quality.


Phone: 786.219.1010
Email: sales@tractopart.com
Main Office: 3505 South Ocean Drive #204
Hollywood, FL 33019